Wedding

Metal detector attachment with one transistor. Homemade metal detectors, or how to make a metal detector with your own hands. Brief instructions for setting up a DIY metal detector “Pirate”

With the onset of spring, more and more often you can see people with metal detectors on the banks of rivers. Most of them are engaged in “gold mining” purely out of curiosity and passion. But a certain percentage actually earn a lot of money from searching for rare things. The secret to the success of such research is not only in experience, information and intuition, but also in the quality of the equipment with which they are equipped. A professional instrument is expensive, and if you have a basic knowledge of radio mechanics, you have probably thought more than once about how to make a metal detector with your own hands. The editors of the site will come to your aid and tell you today how to assemble the device yourself using diagrams.

Read in the article:

Metal detector and its structure

This model costs more than 32,000 rubles, and, of course, non-professionals will not be able to afford such a device. Therefore, we suggest studying the design of a metal detector in order to assemble a variation of such a device yourself. So, the simplest metal detector consists of the following elements.

The operating principle of such metal detectors is based on the transmission and reception of electromagnetic waves. The main elements of a device of this type are two coils: one is transmitting, and the second is receiving.

The metal detector works like this: the magnetic field lines of the primary field (A) of red color pass through the metal object (B) and create a secondary field (green lines) in it. This secondary field is picked up by the receiver and the detector sends an audible signal to the operator. Based on the principle of operation of emitters, electronic devices of this type can be divided into:

Simple, working on the “receive-transmit” principle.
Induction.
Pulse.
Generating.

The cheapest devices belong to the first type.

An induction metal detector has one coil that sends and receives a signal simultaneously. But devices with pulse induction differ in that they generate a transmitter current, which turns on for a while and then turns off abruptly. The coil field generates pulsed eddy currents in the object, which are detected by analyzing the attenuation of the pulse induced in the receiver coil. This cycle repeats continuously, perhaps hundreds of thousands of times per second.

How does a metal detector work depending on its purpose and technical device?

The operating principle of a metal detector varies depending on the type of device. Let's consider the main ones:

Dynamic type devices. The simplest type of device that continuously scans the field. The main feature of working with such a device is that you must be in motion all the time, otherwise the signal will disappear. Such devices are easy to use, however, they are poorly sensitive.
Pulse type devices. They have great sensitivity. Often, such a device comes with several additional coils for adjustment to different types of soils and metals. Requires certain skills to set up. Among the devices of this class we can distinguish electronic devices operating at low frequencies - no higher than 3 kHz.

Electronic devices, on the one hand, do not give a reaction (or give a weak one) to unwanted signals: wet sand, small pieces of metal, shot, for example, and, on the other hand, they provide good sensitivity when searching for hidden water pipes and central heating routes, as well as coins and other metal objects.
Depth detectors designed to search for objects located at impressive depths. They can detect metal objects at a depth of up to 6 meters, while other models “pierce” only up to 3. For example, the Jeohunter 3D depth detector is capable of searching and detecting voids and metals, while showing objects found in the ground in 3- measured form.

Depth detectors operate on two coils, one is parallel to the ground surface, the other is perpendicular.

Stationary detectors- these are frames established at particularly important protected sites. They detect any metal objects in people's bags and pockets that pass through the circuit.

Which metal detectors are suitable for making yourself at home?

The simplest devices that you can assemble yourself include devices that operate on the principle of reception and transmission. There are schemes that even a novice radio amateur can do; for this you just need to select a certain set of parts.

There are many video instructions on the Internet with detailed explanations of how to make a simple metal detector with your own hands. Here are the most popular ones:

Metal detector "Pirate".
Metal detector - butterfly.
Emitter without microcircuits (IC).
Series of metal detectors "Terminator".

However, despite the fact that some entertainers are trying to offer systems for assembling a metal detector from a phone, such designs will not pass the battle test. It’s easier to buy a children’s metal detector toy, it will be more useful.

And now more about how to make a simple metal detector with your own hands using the example of the “Pirate” design.

Homemade metal detector “Pirate”: diagram and detailed description of the assembly

Homemade products based on the “Pirate” series metal detector are among the most popular among radio amateurs. Thanks to the good performance of the device, it can “detect” an object at a depth of 200 mm (for small items) and 1500 mm (large items).

Parts for assembling a metal detector

The Pirate metal detector is a pulse type device. To make the device you will need to purchase:

Materials for making the body, rod (you can use a plastic pipe), holder, and so on.
Wires and electrical tape.
Headphones (suitable for the player).
Transistors – 3 pieces: BC557, IRF740, BC547.
Microcircuits: K157UD2 and NE
Ceramic capacitor - 1 nF.
2 film capacitors - 100 nF.
Electrolytic capacitors: 10 μF (16 V) – 2 pieces, 2200 μF (16 V) – 1 piece, 1 μF (16 V) – 2 pieces, 220 μF (16 V) – 1 piece.
Resistors – 7 pieces per 1; 1.6; 47; 62; 100; 120; 470 kOhm and 6 pieces for 10, 100, 150, 220, 470, 390 Ohm, 2 pieces for 2 Ohm.
2 diodes 1N148.

DIY metal detector circuits

The classic circuit of the “Pirate” series metal detector is built using the NE555 microcircuit. The operation of the device depends on a comparator, one output of which is connected to the IC pulse generator, the second to the coil, and the output to the speaker. If metal objects are detected, the signal from the coil is sent to the comparator, and then to the speaker, which notifies the operator of the presence of the desired objects.

The board can be placed in a simple junction box, which can be purchased at an electrical store. If such a tool is not enough for you, you can try to make a more advanced device; a diagram for making a gold-oriented metal detector will help you.

How to assemble a metal detector without using microcircuits

This device uses Soviet-style transistors KT-361 and KT-315 to generate signals (you can use similar radio components).

How to assemble a metal detector circuit board with your own hands

The pulse generator is assembled on the NE555 chip. By selecting C1 and 2 and R2 and 3, the frequency is adjusted. The pulses obtained as a result of scanning are transmitted to transistor T1, and it transmits the signal to transistor T2. The audio frequency is amplified using the BC547 transistor to the collector, and headphones are connected.

To place radio components, a printed circuit is used, which can be easily made independently. To do this, we use a piece of sheet getinax covered with copper electrical foil. We transfer the connecting parts onto it, mark the fastening points, and drill holes. We cover the tracks with a protective varnish, and after drying, we lower the future board into ferric chloride for etching. This is necessary to remove unprotected areas of copper foil.

How to make a metal detector coil with your own hands

For the base you will need a ring with a diameter of about 200 mm (ordinary wooden hoops can be used as the base), on which 0.5 mm wire is wound. To increase the depth of metal detection, the coil frame should be in the range of 260−270 mm, and the number of turns should be 21−22 vol. If you don't have anything suitable on hand, you can wind a reel on a wooden base.

Copper wire spool on wooden base

Illustration	Description of action
	For winding, prepare a board with guides. The distance between them is equal to the diameter of the base on which you will attach the reel.
	Wind the wire around the perimeter of the fastenings in 20-30 turns. Secure the winding with electrical tape in several places.
	Remove the winding from the base and give it a rounded shape; if necessary, additionally fasten the winding in several more places.
	Connect the circuit to the device and test its operation.

Twisted pair coil in 5 minutes

We will need: 1 twisted pair 5 cat 24 AVG (2.5 mm), knife, soldering iron, solder and multitester.

Illustration	Description of action
	Twist the wire into two skeins. Leave 10 cm on each side.
	Strip the winding and free the wires for connection.
	We connect the wires according to the diagram.
	For better fastening, solder them with a soldering iron.
	Test the coil in the same manner as the copper wire device. The winding terminals must be soldered to a stranded wire with a diameter in the range of 0.5-0.7 mm.

Brief instructions for setting up a DIY metal detector “Pirate”

Once the main elements of the metal detector are ready, we proceed to assembly. We attach all the components to the metal detector rod: the body with the coil, the receiving and transmitting unit and the handle. If you did everything correctly, then additional manipulations with the device will not be required, since it initially has maximum sensitivity. Fine tuning is performed using variable resistor R13. Normal operation of the detector should be ensured with the regulator in the middle position. If you have an oscilloscope, then use it to measure the frequency at the gate of transistor T2, which should be 120−150 Hz, and the pulse duration should be 130−150 μs.

Is it possible to make an underwater metal detector with your own hands?

The principle of assembling an underwater metal detector is no different from a conventional one, with the only difference being that you will have to work hard to create an impenetrable shell using sealant, as well as to place special light indicators that can report a find from under water. An example of how this will work is in the video:

Do-it-yourself metal detector “Terminator 3”: detailed diagram and video instructions for assembly

The Terminator 3 metal detector has occupied an honorable place among homemade metal detectors for many years. The two-tone device operates on the principle of induction balance.

Its main features are: low power consumption, metal discrimination, non-ferrous metals mode, gold only mode and very good search depth characteristics, compared to semi-professional branded metal detectors. We offer you the most detailed description of the assembly of such a device from folk craftsman Viktor Goncharov.

How to make a metal detector with your own hands with metal discrimination

Metal discrimination is the ability of the device to distinguish between the detected material and classify it. Discrimination is based on different electrical conductivities of metals. The simplest methods for determining the types of metals were implemented in old instruments and entry-level devices and had two modes - “all metals” and “non-ferrous”. The discrimination function allows the operator to respond to a phase shift of a certain magnitude, compared to a configured (reference) level. In this case, the device cannot distinguish between non-ferrous metals.

Learn how to make a homemade professional metal detector using improvised materials in this video:

Features of deep metal detectors

Metal detectors of this type can detect objects at great depths. A good metal detector, made by yourself, looks to a depth of 6 meters. However, in this case the size of the find must be substantial. These detectors work best for detecting old shells or large enough debris.

There are two types of deep metal detectors: frame and transceiver on a rod. The first type of device is capable of covering a large area of land for scanning, however, in this case, the efficiency and focus of the search is reduced. The second version of the detector is a point detector; it works directed inward over a small diameter. You need to work with it slowly and carefully. If your goal is to build such a metal detector, the following video can tell you how to do it.

If you have experience in assembling such a device and using it, tell others about it!

A metal detector is an electronic device for searching and distinguishing metals, metal objects that can be hidden at different depths under a layer of sand, earth, in the walls of rooms and various structures.

Schematic diagrams of metal detectors made on transistors, microcircuits and microcontrollers are given. A factory-made metal detector is a fairly expensive device, so making a homemade metal detector yourself can save quite a bit of money.

The circuits of modern metal detectors can be built according to different operating principles; we list the most popular of them:

Beat method (measuring changes in reference frequency);
Induction balance at low frequencies;
Induction balance on spaced coils;
Pulse method.

Many novice radio amateurs and treasure hunters are wondering: how to make a metal detector yourself? It is advisable to start your acquaintance with assembling a simple metal detector circuit; this will allow you to understand the operation of such a device and gain first skills in searching for treasures and products made of multi-colored metals.

Now there is a fairly large selection of multimeters, at very different prices. Now the radio amateur can not be limited to the modest set of functions of the “legendary” M-838. For slightly more expensive, you can purchase a more modern device that is also capable of measuring the frequency of alternating current...

0 329 0

The metal detector is designed to detect a metal object (well cover, pipe section, hidden wiring). The metal detector consists of a parallel voltage stabilizer (transistors V1 V2) at a high frequency generator (about 100 kHz) on transistor V4, an RF vibration detector (V5) and...

13 5435 6

The metal detector allows you to detect any metal object at a distance of up to 20 cm. The detection range depends only on the area of the metal object. For those for whom this distance is not enough, for example treasure hunters, we can recommend increasing the size of the frame. This should also increase the detection depth. The schematic diagram of the metal detector is shown in the figure. The circuit is assembled using transistors operating in...

9 4988 1

Circuit diagram of a homemade beat metal detector, which is built on five microcircuits. Finds a 0.25mm coin at a depth of 5cm, a pistol at a depth of 10cm, and a metal helmet at 20cm. The schematic diagram of a beat metal detector is shown below. The circuit consists of the following components: a crystal oscillator, a measuring oscillator, a synchronous detector, a Schmidt trigger, an indication device...

11 5122 4

The circuit shown in the figure is a classic metal detector. The operation of the circuit is based on the principle of superheterodyne frequency conversion, which is usually used in a superheterodyne receiver. Schematic diagram of a metal detector with an integrated ULF; it uses two radio frequency generators, the frequencies of which are 5.5 MHz. The first radio frequency generator is assembled on a T1 transistor type BF494, frequency...

5 5118 2

This metal detector, despite the small number of parts and ease of manufacture, is quite sensitive. It can detect large metal objects, such as a heating battery, at a distance of up to 60 cm, while small ones, for example, a coin with a diameter of 25 mm, can be detected at a distance of 15 cm. The operating principle of the device is based on a change in frequency in the measuring generator under the influence of nearby metals and. ..

19 5048 0

A simple compact metal detector is needed to detect various metal objects (for example, pipes, wiring, nails, fittings) in walls under a layer of plaster. This device is completely autonomous, powered by a 9-volt Krona battery, consuming 4-5 mA from it. The metal detector has sufficient sensitivity to detect: pipes at a distance of 10-15 cm; wiring and nails at a distance of 5-10...

8 4915 0

Scheme of a small-sized, highly economical metal detector with good repeatability and high performance characteristics, using widely available and inexpensive parts. An analysis of most common circuits has shown that they are all powered from a source with a voltage of at least 9 V (that is, “Krona”), and this is both expensive and uneconomical. So, assembled on the K561LE5 chip...

18 5688 1

I can say without a doubt that this is the simplest metal detector I have ever seen. It is based on just one TDA0161 chip. You won't need to program anything - just assemble it and that's it. Another great difference is that it does not make any sounds during operation, unlike a metal detector based on the NE555 chip, which initially beeps unpleasantly and you have to guess the metal found by its tone.

In this circuit, the buzzer starts beeping only when it detects metal. The TDA0161 chip is a specialized industrial version for induction sensors. And metal detectors for production are mainly built on it, giving a signal when metal approaches the induction sensor.
You can purchase such a microcircuit at -
It is not expensive and is quite accessible to everyone.

Here is a diagram of a simple metal detector

Metal detector characteristics

Microcircuit power supply voltage: from 3.5 to 15V
Generator frequency: 8-10 kHz
Current consumption: 8-12 mA in alarm mode. In search state approximately 1 mA.
Operating temperature: -55 to +100 degrees Celsius

The metal detector is not only very economical, but also very unpretentious.
An old cell phone battery works well for power supply.
Coil: 140-150 turns. The diameter of the coil is 5-6 cm. Can be converted to a coil of larger diameter.

The sensitivity will depend directly on the size of the search coil.
In the scheme I use both light and sound signaling. You can choose one if you want. Buzzer with internal generator.
Thanks to this simple design, you can make a pocket metal detector or a large metal detector, depending on what you need more.

After assembly, the metal detector works immediately and does not require any adjustments, except for setting the response threshold with a variable resistor. Well, this is standard procedure for a metal detector.
So, friends, collect the things you need and, as they say, they will come in handy around the house. For example, to search for electrical wiring in a wall, even nails in a log...

Many radio amateurs dream of making a metal detector with their own hands. It can be used to detect metal objects in the ground at different depths. On the Internet you can find many photos of metal detector circuits that are simple to use. Any beginning radio amateur can make them.

Easy assembly

For example, let's take the circuit of a simple metal detector. It is of the pulse type, but due to the simplicity of its design it is not able to distinguish between types of metals. Therefore, it will not be possible to operate such a device in areas where objects made of non-ferrous metal are found.

How to assemble the device

To assemble a simple metal detector circuit with your own hands, you will need the following tools and parts:

Presence of KR1006VI1 microcircuit and IRF740 transistor;
Presence of K157UD2 microcircuit and VS547 transistor;
Copper conductor 0.5mm (PEV);
NPN transistor;
Housing, and various materials for it;
Solder, flux, soldering iron.

Other details are shown in the diagram. In order for the assembled circuit to be securely fastened, a plastic case should be prepared for it.

The bar can be made using a small diameter plastic tube. A metal detecting coil will be installed in its lower part.

Beginning of work

The circuit diagram of a metal detector using transistors is a common option for many models. Assembly begins with the manufacture of a printed circuit board. Next, all radio elements are mounted on it exactly as shown in the diagram.

To ensure stable operation of the device, film capacitors are used in the circuit. This will allow you to use it in cold weather without any problems.

Power type for device

The device can operate on a voltage of 9-12 V. Due to its sufficient power, energy is intensively consumed. It is recommended to install up to 3 batteries and connect them in a parallel circuit. You can use a small battery that has a charger. Thanks to its capacity, the metal detector will work longer.

Coil installation

There are different types and schemes for the manufacture of metal detectors, but in the pulsed version, inaccuracies are allowed in the installation of the coil. When making a mandrel, the winding should be up to 25 turns, and the diameter of the ring should be 1900-200mm.

All turns of the coil must be insulated with electrical tape. Reducing the number of turns to 22, and the mandrel diameter of 270 mm will allow you to detect objects at a deeper location. The wire cross-section on the coil is 0.5 mm.

When the winding is ready, it is attached to a durable housing with sufficient rigidity, on which there should be no metal parts. Otherwise, they are able to shield the magnetic field, and the operation of the metal detector will be disrupted. The body can be made of wood or plastic, but so that it can withstand various impacts that can damage the coil.

The leads on it should be soldered to a conductor of several cores. The best option is a two-core wire.

The installation of a non-ferrous metal detector circuit is a little more complicated, and high precision must be observed in the manufacture of the coil. The number of turns reaches 100pcs, and a vinyl tube is used as the core. Foil is wound on top of the winding, which forms an electrostatic screen.

Device setup

If the installation of the circuit is done exactly, then the metal detector will not need additional settings. Its sensitivity indicators will be maximum, but fine adjustment is possible through variable resistance R13. It must be performed until rare clicks begin in the headphones.

If the adjustment fails, then the resistances must be replaced with R12. When the resistor adjustment is in the middle, this will be considered normal.

An oscilloscope is suitable for checking the device. The frequency of transistor T2 is measured on it, and the pulse should last up to 150 ms. The optimal operating frequency is up to 150 Hz.

How to use the device

You should not rush and start working immediately after turning on the metal detector. It should stabilize, so you need to wait up to 20 seconds. After adjusting the resistor appropriately, you can start looking for metal.

Note!

Photo of the metal detector circuit

Note!

A device that allows you to search for metal objects located in a neutral environment, such as soil, due to their conductivity is called a metal detector (metal detector). This device allows you to find metal objects in various environments, including in the human body.

Largely thanks to the development of microelectronics, metal detectors, which are produced by many enterprises around the world, are highly reliable and have small overall and weight characteristics.

Not so long ago, such devices could most often be seen among sappers, but now they are used by rescuers, treasure hunters, and utility workers when searching for pipes, cables, etc. Moreover, many “treasure hunters” use metal detectors, which they assemble with their own hands .

Design and principle of operation of the device

Metal detectors on the market operate on different principles. Many believe that they use the principle of pulse echo or radar. Their difference from locators lies in the fact that the transmitted and received signals act constantly and simultaneously; in addition, they operate at the same frequencies.

Devices operating on the “receive-transmit” principle record the signal reflected (re-emitted) from a metal object. This signal appears due to the exposure of a metal object to an alternating magnetic field generated by the metal detector coils. That is, the design of devices of this type provides for the presence of two coils, the first is transmitting, the second is receiving.

Devices of this class have the following advantages:

simplicity of design;
Great potential for detecting metallic materials.

At the same time, metal detectors of this class have certain disadvantages:

metal detectors can be sensitive to the composition of the soil in which they search for metal objects.
technological difficulties in the production of the product.

In other words, devices of this type must be configured with your own hands before work.

Other devices are sometimes called beat metal detectors. This name comes from the distant past, more precisely from the times when superheterodyne receivers were widely used. Beating is a phenomenon that becomes noticeable when two signals with similar frequencies and equal amplitudes are summed. The beat consists of pulsating the amplitude of the summed signal.

The signal pulsation frequency is equal to the difference in the frequencies of the summed signals. By passing such a signal through a rectifier, it is also called a detector, and the so-called difference frequency is isolated.

This scheme has been used for a long time, but nowadays it is not used. They were replaced by synchronous detectors, but the term remained in use.

A beat metal detector works using the following principle - it registers the difference in frequencies from two generator coils. One frequency is stable, the second contains an inductor.

The device is configured with your own hands so that the generated frequencies match or at least are close. As soon as metal enters the action zone, the set parameters change and the frequency changes. The frequency difference can be recorded in a variety of ways, from headphones to digital methods.

Devices of this class are characterized by a simple sensor design and low sensitivity to the mineral composition of the soil.

But besides this, when using them, it is necessary to take into account the fact that they have high energy consumption.

Typical design

The metal detector includes the following components:

The coil is a box-type structure that houses the signal receiver and transmitter. Most often, the coil has an elliptical shape and polymers are used for its manufacture. A wire is connected to it connecting it to the control unit. This wire transmits the signal from the receiver to the control unit. The transmitter generates a signal when metal is detected, which is transmitted to the receiver. The coil is installed on the lower rod.
The metal part on which the reel is fixed and its angle of inclination is adjusted is called the lower rod. Thanks to this solution, a more thorough examination of the surface occurs. There are models in which the lower part can adjust the height of the metal detector and provides a telescopic connection to the rod, which is called the middle one.
The middle rod is the unit located between the lower and upper rods. Devices are attached to it that allow you to adjust the size of the device. On the market you can find models that consist of two rods.
The top rod usually has a curved appearance. It resembles the letter S. This shape is considered optimal for attaching it to the hand. An armrest, a control unit and a handle are installed on it. The armrest and handle are made of polymer materials.
The metal detector control unit is necessary to process the data received from the coil. After the signal is converted, it is sent to headphones or other display devices. In addition, the control unit is designed to regulate the operating mode of the device. The wire from the coil is connected using a quick release device.

All devices included in the metal detector are waterproof.

It is this relative simplicity of design that allows you to make metal detectors with your own hands.

Types of metal detectors

There is a wide range of metal detectors on the market, used in many areas. Below is a list that shows some of the varieties of these devices:

Most modern metal detectors can find metal objects at a depth of up to 2.5 m; special deep products can detect a product at a depth of up to 6 meters.

Operating frequency

The second parameter is the operating frequency. The thing is that low frequencies allow the metal detector to see to a fairly large depth, but they are not able to see small details. High frequencies allow you to notice small objects, but do not allow you to view the ground to great depths.

The simplest (budget) models operate at one frequency; models that fall into the middle price range use 2 or more frequencies. There are models that use 28 frequencies when searching.

Modern metal detectors are equipped with a function such as metal discrimination. It allows you to distinguish the type of material located at depth. In this case, when ferrous metal is detected, one sound will sound in the search engine’s headphones, and when non-ferrous metal is detected, another sound will sound.

Such devices are classified as pulse-balanced. They use frequencies from 8 to 15 kHz in their work. Batteries of 9 - 12 V are used as a source.

Devices of this class are capable of detecting a gold object at a depth of several tens of centimeters, and ferrous metal products at a depth of about 1 meter or more.

But, of course, these parameters depend on the device model.

How to assemble a homemade metal detector with your own hands

There are many models of devices on the market for detecting metal in the ground, walls, etc. Despite its external complexity, making a metal detector with your own hands is not that difficult and almost anyone can do it. As noted above, any metal detector consists of the following key components - a coil, a decoder and a power supply signaling device.

To assemble such a metal detector with your own hands, you need the following set of elements:

controller;
resonator;
capacitors of various types, including film ones;
resistors;
sound emitter;
Voltage regulator.

Do-it-yourself simple metal detector

The metal detector circuit is not complicated, and you can find it either on the vast world wide web or in specialized literature. Above is a list of radio elements that are useful for assembling a metal detector with your own hands at home. You can assemble a simple metal detector with your own hands using a soldering iron or other available method. The main thing is that the parts should not touch the body of the device. To ensure the operation of the assembled metal detector, power supplies of 9 - 12 volts are used.

To wind the coil, use a wire with a cross-sectional diameter within 0.3 mm; of course, this will depend on the chosen circuit. By the way, the wound coil must be protected from exposure to extraneous radiation. To do this, shield it with your own hands using ordinary food foil.

To flash the controller firmware, special programs are used, which can also be found on the Internet.

Metal detector without chips

If a novice “treasure hunter” has no desire to get involved with microcircuits, there are circuits without them.

There are simpler circuits based on the use of traditional transistors. Such a device can find metal at a depth of several tens of centimeters.

Deep metal detectors are used to search for metals at great depths. But it is worth noting that they are not cheap and therefore it is quite possible to assemble it yourself. But before you start making it, you need to understand how a typical circuit works.

The circuit of a deep metal detector is not the simplest and there are several options for its implementation. Before assembling it, you need to prepare the following set of parts and elements:

capacitors of various types - film, ceramic, etc.;
resistors of different values;
semiconductors - transistors and diodes.

Nominal parameters and quantity depend on the selected circuit diagram of the device. To assemble the above elements, you will need a soldering iron, a set of tools (screwdriver, pliers, wire cutters, etc.), and material for making the board.

The process of assembling a deep metal detector looks something like this. First, a control unit is assembled, the basis of which is a printed circuit board. It is made from textolite. Then the assembly diagram is transferred directly to the surface of the finished board. After the drawing is transferred, the board must be etched. To do this, use a solution that includes hydrogen peroxide, salt, and electrolyte.

After the board is etched, it is necessary to make holes in it to install the circuit components. After tinning the board. The most important stage is coming. Do-it-yourself installation and soldering of parts onto a prepared board.

To wind the coil with your own hands, use PEV brand wire with a diameter of 0.5 mm. The number of turns and the diameter of the coil depend on the selected circuit of the deep metal detector.

A little about smartphones

There is an opinion that it is quite possible to make a metal detector from a smartphone. This is wrong! Yes, there are applications that install under Android OS.

But in fact, after installing such an application, he will actually be able to find metal objects, but only pre-magnetized ones. It will not be able to search for, much less discriminate against, metals.