Tank ammo. Armor-piercing kinetic shells and rockets Caliber of tank shells

MOSCOW, July 23 - RIA Novosti, Andrey Kots. If a modern tank is fired upon with an armor-piercing "blank" from the Second World War, then, most likely, only a dent will remain at the site of impact - penetrating through is practically impossible. The "puff" used today composite armor confidently holds such a blow. But it can still be pierced with an "awl". Or "crowbar", as the tankers themselves call armor-piercing feathered sub-caliber shells (BOPS). About how these munitions work - in the material of RIA Novosti.

Awl instead of a sledgehammer

From the name it is clear that the sub-caliber ammunition is a projectile with a caliber noticeably smaller than the caliber of the gun. Structurally, this is a "coil" with a diameter equal to the diameter of the barrel, in the center of which is the same tungsten or uranium "scrap" that hits the enemy's armor. When leaving the bore, the coil, which provided the core with sufficient kinetic energy and accelerated it to the desired speed, is divided into parts under the action of oncoming air flows, and a thin and strong feathered pin flies at the target. In a collision, due to its lower resistivity, it penetrates armor much more efficiently than a thick monolithic blank.

The armored impact of such a "scrap" is colossal. Due to the relatively small mass - 3.5-4 kilograms - the core of the sub-caliber projectile immediately after the shot accelerates to a significant speed - about 1500 meters per second. When hitting the armor plate, it punches a small hole. The kinetic energy of the projectile is partly used to destroy armor, and partly converted into heat. Red-hot fragments of the core and armor go into the armored space and spread like a fan, hitting the crew and internal mechanisms of the vehicle. This creates multiple fires.

An accurate hit of the BOPS can disable important components and assemblies, destroy or seriously injure crew members, jam the turret, break through fuel tanks, undermine the ammunition rack, destroy the undercarriage. Structurally, modern sabots are very different. Projectile bodies are both monolithic and composite - a core or several cores in a shell, as well as longitudinally and transversely multilayered, with various types of plumage.

Leading devices (those same "coils") have different aerodynamics, they are made of steel, light alloys, as well as composite materials - for example, carbon composites or aramid composites. Ballistic tips and dampers can be installed in the head parts of the BOPS. In a word, for every taste - for any gun, for certain conditions of tank combat and a specific target. The main advantages of such ammunition are high armor penetration, high flight speed, low sensitivity to dynamic protection, low vulnerability to active protection systems, which simply do not have time to react to a fast and inconspicuous "arrow".

"Mango" and "Lead"

For 125 mm smoothbore guns domestic tanks also in Soviet time developed a wide range of feathered "armor-piercing". They were engaged after the appearance of the potential enemy tanks M1 Abrams and Leopard-2. The army, like air, needed shells capable of hitting new types of reinforced armor and overcoming dynamic protection.

One of the most common BOPS in the arsenal of Russian T-72, T-80 and T-90 tanks is the ZBM-44 "Mango" high-power projectile, which was put into service in 1986. Ammunition has a rather complicated design. A ballistic tip is installed in the head part of the swept body, under which there is an armor-piercing cap. Behind him is an armor-piercing damper, which also plays an important role in breaking through. Immediately after the damper are two tungsten alloy cores held inside by a light-alloy metal jacket. When a projectile collides with an obstacle, the shirt melts and releases cores that "bite" into the armor. In the tail of the projectile there is a stabilizer in the form of a plumage with five blades, at the base of the stabilizer there is a tracer. This "scrap" weighs only about five kilograms, but is capable of penetrating almost half a meter of tank armor at a distance of up to two kilometers.

The newer ZBM-48 "Lead" was put into service in 1991. Standard Russian tank autoloaders are limited by the length of the shells, so Lead is the most massive domestic tank ammunition of this class. The length of the active part of the projectile is 63.5 centimeters. The core is made of a uranium alloy, it has a high elongation, which increases penetration, and also reduces the impact of dynamic protection. After all, the longer the projectile, the smaller part of it interacts with passive and active obstacles at a certain point in time. Sub-caliber stabilizers improve the accuracy of the projectile, and a new composite "coil" drive device is also used. BOPS "Lead" is the most powerful serial projectile for 125-mm tank guns, capable of competing with leading Western models. The average armor penetration on a homogeneous steel plate from two kilometers is 650 millimeters.

This is not the only such development of the domestic defense industry - the media reported that specifically for the latest T-14 "Armata" tank, BOPS "Vacuum-1" with a length of 900 millimeters were created and tested. Their armor penetration came close to a meter.

It is worth noting that the potential enemy also does not stand still. Back in 2016, Orbital ATK launched a full-scale production of an advanced armor-piercing feathered sub-caliber projectile with a fifth-generation M829A4 tracer for the M1 tank. According to the developers, the ammunition penetrates 770 millimeters of armor.

One of the tasks of the modern basic battle tank is the destruction of similar enemy equipment, for which he needs a powerful weapon and appropriate armor-piercing shells. Russian tanks are armed with several anti-tank munitions that allow them to deal with well-protected enemy vehicles. In addition, in the near future, new samples intended for use with weapons of advanced technology should go into large-scale production.

Armor-piercing feathered sub-caliber projectiles (BOPS) show the highest armor penetration characteristics. Such ammunition appeared several decades ago, and later proved to be a convenient means of destroying armored vehicles with powerful protection different types. As a result, at present, it is BOPS that turn out to be the main tool for tanks to fight other tanks. The development of this class of projectiles continues.

Serial "Mango"

According to various sources, Russian armored units are currently armed with several types of BOPS, and the most massive representative of this class is the 3BM-42 Mango product. The development of a new projectile with increased power under the code "Mango" began in the first half of the eighties. Through the use of certain materials, technologies and solutions, it was necessary to increase armor penetration in comparison with existing projectiles. The future projectile 3BM-42 was supposed to be used with the existing tank guns of the 2A46 family.

The T-72B3 main tank carries an improved automatic loader compatible with extended projectile lengths. Photo Vitalykuzmin.net

A few years later, the 3VBM-17 round with the 3BM-42 BOPS entered service. It includes the so-called. a burning cylinder, inside of which a driving device with a projectile is rigidly attached. Also, a separate partially combustible cartridge case with means of ignition is used for the shot. The cavities of the sleeve and cylinder are filled with tubular powder, which ensures the acceleration of the projectile.

The creators of the Mango projectile coped with the task of increasing armor penetration, and they did it very interesting way. The projectile has a special design, due to which an increase in the main characteristics is achieved. At the same time, outwardly, 3BM-42 is almost no different from other products of its class. This BOPS is a hollow cylindrical body of small diameter, made of steel and equipped with a tail stabilizer. The front end of the body is closed with a ballistic cap and the so-called. armor-piercing damper. Two tungsten cores are located one behind the other in the housing cavity, held in place by a low-melting metal jacket.

A resettable lead device made of aluminum is installed on the projectile. It has a conical shape with a widening front. Interaction with the bore is provided by several rings on the outer surface of the device. Shot 3VBM-17, including a cylinder, a projectile and a leading device, has a length of 574 mm with a diameter of 125 mm. The mass of the projectile itself is 4.85 kg.

Shot 3VBM-17 with a projectile 3BM-42 "Mango". Photo Fofanov.armor.kiev.ua

The combustion of gunpowder in the sleeve and cylinder makes it possible to accelerate the projectile with the driving device to a speed of no more than 1700 m / s. After exiting the barrel, the master device is reset. Upon hitting the target, the holding jacket melts, after which tungsten cores can pierce armor. The maximum armor penetration at a distance of 2 km is determined as 500 mm. With a meeting angle of 60 ° at the same distance, this characteristic is reduced to 220 mm.

The 3VBM-17 shot with the 3BM-42 projectile was put into service in 1986 and had a noticeable effect on fighting qualities all existing main tanks of the Soviet army. This product is still used in tank troops and is almost the basis of their arsenals. Subsequently, modernization was carried out, which consisted in increasing the length of the body and cores. As a result, "Mango-M" weighs 5 kg and can penetrate up to 270 mm of armor at an angle of 60 °.

Long way "Lead"

Soon after the appearance of the Mango BOPS, well-known unpleasant events began in our country that hit a lot of areas, including the development of promising shells for tank guns. Only by the end of the nineties was it possible to obtain real results in the form of another projectile with improved performance. This ammunition was the result of development work with the code "Lead".

Scheme of the product "Mango". Figure Btvt.narod.ru

Experience has shown that a further increase in the main combat characteristics is associated with a mandatory increase in the length of the projectile. This parameter was increased to 740 mm, but this fact did not allow the use of the future projectile with existing tank loaders. As a result, the next project for the modernization of armored vehicles had to include an update of the automation that serves the gun.

From the point of view of the general appearance, the 3VBM-20 shot with the 3BM-46 "Lead-1" projectile is somewhat similar to the older 3VBM-17 and also consists of a projectile in a burning cylinder and a cartridge case with a metal pallet. At the same time, the design of the projectile itself is seriously different from the existing one. This time it was decided to use a monolithic depleted uranium core (according to other sources, from a tungsten alloy), which is actually the basis of the projectile. A ballistic cap and tail stabilizers are attached to the metal core, the diameter of which is less than the caliber of the barrel.

For a longer projectile, an improved lead device was created. It is distinguished by its large length and the presence of two contact zones. In front of the device there is a large cylinder of the usual type, and the second zone is created by three rear supports. After exiting the barrel, such a master device is reset and releases the projectile.

"Mango-M" and a cartridge case with a propelling charge. Photo btvt.narod.ru

According to available data, Lead-1 has a mass of 4.6 kg and is capable of accelerating to a speed of 1750 m/s. Due to this, it penetrates up to 650 mm of homogeneous armor at a shot distance of 2000 m and a zero encounter angle. It is known about the existence of the "Lead-2" project, which provided for the replacement of the core with a product made of another material. Thus, similar shells from uranium and tungsten could appear in the arsenals.

Due to its long length, the new type of projectile could not be used with existing automatic loaders for mass-produced tanks. This problem was solved in the middle of the 2000s. The T-90A armored vehicles of the new series were equipped with modified machine guns compatible with "long" shells. In the future, the upgraded T-72B3 began to receive similar equipment. Thus, a significant part of the equipment of the armored forces can use not only the relatively old "Mango" with limited characteristics.

"Vacuum" for "Armata"

Observed increase in tank protection characteristics potential adversary is a real challenge for weapons developers. Further research work led to the conclusion about the need for a new increase in the length of the ammunition. The BOPS 1000 mm long could show the optimal ratio of characteristics, but such a projectile, for obvious reasons, could not be used with the 2A46 gun and its automatic loader.

Projectile 3BM-46 with a leading device. Photo Fofanov.armor.kiev.ua

The way out of this situation was the creation of a completely new weapon with additional equipment. The promising gun later became known under the index 2A82, and the new projectile received the code "Vacuum". From a certain time, a new weapon system began to be considered in the context of the project of the promising Armata tank. In case of successful completion of work on the gun and BOPS, new tank could get them as the main weapon.

According to some sources, the Vacuum project was turned off in favor of new developments. In connection with the start of the development of the 2A82-1M gun, instead of such a projectile, it was proposed to create a smaller BOPS with the code "Vacuum-1". It was supposed to have a length of "only" 900 mm and be equipped with a carbide core. In the recent past, representatives of the defense industry mentioned that organizations from Rosatom were involved in the development of a new projectile. Their participation is due to the need to use depleted uranium.

According to some reports, a projectile called "Vacuum-2" is being created in parallel. In its design, it should be similar to a product with a unit, but at the same time differ in material. It is proposed to make it from a tungsten alloy, more familiar to domestic BOPS. Also, for use with the 2A82-M gun, a high-explosive fragmentation munition with a controlled detonation with the Telnik code and a 3UBK21 Sprinter guided missile are being created. Accurate information about the creation of a new 125-mm cumulative projectile is not yet available.

Main tank T-14 with 2A82-1M gun. Photo by NPK "Uralvagonzavod" / uvz.ru

The appearance and exact technical characteristics of the promising BOPS of the Vacuum family have not yet been specified. It is only known that a projectile with a uranium core will penetrate about 900-1000 mm of homogeneous armor. Probably, such characteristics can be obtained with an ideal angle of impact. Other details are missing.

Promising "Slate"

According to various reports of past years, promising domestically developed tanks were also supposed to receive an armor-piercing projectile called the Lead. However, there was not too much information about him, which led to confusion and misconceptions. So, for some time it was believed that the "Slate" was intended for new 125-mm guns. It is now known that this product is planned to be used with a more powerful 152 mm 2A83 gun.

Apparently, the projectile for high-powered cannons will be similar in appearance to other representatives of its class. It will receive a high elongation core equipped with a ballistic cap and an armor-piercing damper in the head part, as well as a relatively small-caliber stabilizer. Earlier it was reported that the "Grifel-1" and "Grifel-2" projectiles will be equipped with tungsten and uranium cores. At the same time, there are no data on the parameters of the armor penetration of new shells.

Models of 125-mm guns 2A82-1M. Photo Yuripasholok.livejournal.com

According to various estimates, based on the caliber and estimated energy indicators, the Leads will be able to penetrate at least 1000-1200 mm of homogeneous armor at the optimal angle of impact. However, there are reports of some characteristic problems in the development of such ammunition. Due to certain objective limitations, the efficiency of using shot energy for 152-mm guns may be lower than for systems of a smaller caliber. Whether it will be possible to cope with such problems and fully use the energy reserve of the propellant charge is unknown.

The promising 2A83 tank gun is currently being developed in the context of the further development of the Armata unified tracked platform. The already created main tank T-14 is equipped with an uninhabited turret with a 2A82-1M gun. In the foreseeable future, it is expected that new version tank, featuring a different fighting compartment and a more powerful 2A83 gun. Along with them, the improved Armata will also receive the BOPS of the Grifel line.

Shells of the present and future

At present, the armored forces are armed with several armor-piercing feathered sub-caliber shells, designed for use with tools of a rather old, but successful 2A46 line. A significant part of the main tanks of existing models has a relatively old automatic loader, and therefore can only use Mango shells and older products. At the same time, late-series T-90A tanks, as well as modernized T-72B3 tanks, are equipped with improved automatic loaders, thanks to which they can use relatively long shells of the Lead line.

The alleged appearance of the BOPS type "Slate". Picture Otvaga2004.mybb.ru

BOPS 3BM-42 and 3BM-46 have fairly high performance, and due to this they are able to deal with a wide range of targets present on the battlefield. At the same time, sub-caliber ammunition is not the only means of combating enemy tanks. For the same purpose, our tanks can use guided missiles and cumulative rounds. Thus, "Mango", "Lead" and other tank ammunition ensure the fight against various targets in a wide range of ranges.

The next generation of Russian tanks, so far represented only by the T-14 Armata, is equipped with a new 2A82-1M gun, which shows higher performance and is compatible with new ammunition. The new family of shells and missiles will provide a noticeable increase in combat qualities and is quite capable of bringing the Armata to a leading position in the world.

It is no secret that in the recent past there has been a significant lag of domestic BOPS from modern foreign models. However, the situation is gradually changing, and new models of this kind are coming into service. In the foreseeable future, armored units will receive fundamentally new combat vehicles with modern weapons and ammunition. There is every reason to believe that the gap will at least narrow. Moreover, one cannot rule out the possibility of being ahead of foreign competitors with understandable consequences for the combat capability of the army.

According to the websites:
http://vpk.mane/
http://ria.ru/
http://tass.ru/
http://otvaga2004.ru/
http://btvt.narod.ru/
http://russianarms.ru/
http://fofanov.armor.kiev.ua/
http://gurkhan.blogspot.com/
http://bmpd.livejournal.com/

The appearance of tanks on the battlefield was one of the most important events in the military history of the last century. Immediately after this moment, the development of means to combat these formidable machines began. If we take a closer look at the history of armored vehicles, then, in fact, we will see the history of the confrontation between the projectile and armor, which has been going on for almost a century.

In this irreconcilable struggle, one or the other side periodically gained the upper hand, which led either to the complete invulnerability of the tanks, or to their huge losses. In the latter case, every time there were voices about the death of the tank and the "end of the tank era." However, today tanks remain the main striking force. ground forces all the armies of the world.

Today, one of the main types of armor-piercing ammunition that are used to combat armored vehicles are sub-caliber ammunition.

A bit of history

The first anti-tank shells were ordinary metal blanks, which, due to their kinetic energy, pierced tank armor. Fortunately, the latter was not very thick, and even anti-tank guns could handle it. However, already before the start of World War II, tanks of the next generation began to appear (KV, T-34, Matilda), with a powerful engine and serious armor.

The major world powers entered World War II with 37 and 47 mm anti-tank artillery and ended it with guns that reached 88 and even 122 mm.

Increasing the caliber of the gun and initial speed projectile flight, the designers had to increase the mass of the gun, making it more complicated, more expensive and much less maneuverable. It was necessary to look for other ways.

And they were soon found: cumulative and sub-caliber ammunition appeared. The action of cumulative ammunition is based on the use of a directed explosion that burns through tank armor, under caliber projectile also does not have a high-explosive effect, it hits a well-protected target due to high kinetic energy.

The design of the sub-caliber projectile was patented back in 1913 by the German manufacturer Krupp, but their mass use began much later. This ammunition does not have a high-explosive effect, it is much more like an ordinary bullet.

For the first time, the Germans began to actively use sub-caliber shells during the French campaign. They had to use such ammunition even more widely after the start of hostilities on the Eastern Front. Only using sub-caliber shells, the Nazis could effectively resist the powerful Soviet tanks.

However, the Germans experienced a serious shortage of tungsten, which prevented them from mass-producing such shells. Therefore, the number of such shots in the ammunition load was small, and the military personnel were given strict orders: to use them only against enemy tanks.

In the USSR, serial production of sub-caliber ammunition began in 1943, they were created on the basis of captured German samples.

After the war, work in this direction continued in most of the world's leading weapons powers. Today, sub-caliber ammunition is considered one of the main means of destroying armored targets.

Currently, there are even sub-caliber bullets that significantly increase the firing range of smoothbore weapons.

Operating principle

What is the basis for the high armor-piercing effect that a sub-caliber projectile has? How is it different from the usual?

A sub-caliber projectile is a type of ammunition with a caliber of the warhead that is many times smaller than the caliber of the barrel from which it was fired.

It was found that a small-caliber projectile flying from high speed, has greater armor penetration than large-caliber. But in order to get high speed after a shot, a more powerful cartridge is needed, which means a gun of a more serious caliber.

It was possible to resolve this contradiction by creating a projectile, in which the striking part (core) has a small diameter compared to the main part of the projectile. The sub-caliber projectile does not have a high-explosive or fragmentation effect, it works on the same principle as a conventional bullet, which hits targets due to high kinetic energy.

The sub-caliber projectile consists of a solid core made of a particularly strong and heavy material, a body (pallet) and a ballistic fairing.

The diameter of the pallet is equal to the caliber of the weapon, it acts as a piston when fired, accelerating the warhead. Leading belts are installed on the pallets of sub-caliber shells for rifled guns. Typically, the pallet is in the form of a coil and is made of light alloys.

There are armor-piercing sub-caliber shells with a non-detachable pallet, from the moment of the shot until the target is hit, the coil and core act as a single whole. This design creates serious aerodynamic drag, significantly reducing flight speed.

Projectiles are considered more advanced, in which, after a shot, the coil is separated due to air resistance. In modern sub-caliber projectiles, the stability of the core in flight is provided by stabilizers. Often a tracer charge is installed in the tail section.

The ballistic tip is made of soft metal or plastic.

The most important element of a sub-caliber projectile is undoubtedly the core. Its diameter is about three times smaller than the caliber of the projectile, and high-density metal alloys are used to make the core: the most common materials are tungsten carbide and depleted uranium.

Due to the relatively small mass, the core of the sub-caliber projectile immediately after the shot accelerates to a significant speed (1600 m / s). Upon impact with the armor plate, the core pierces a relatively small hole in it. The kinetic energy of the projectile is partly used to destroy armor, and partly converted into heat. After breaking through the armor, red-hot fragments of the core and armor go into the armored space and spread like a fan, hitting the crew and internal mechanisms of the vehicle. This creates multiple fires.

As the armor passes, the core grinds and becomes shorter. Therefore, a very important characteristic that affects armor penetration is the length of the core. Also, the effectiveness of the sub-caliber projectile is affected by the material from which the core is made and the speed of its flight.

The latest generation of Russian sub-caliber projectiles ("Lead-2") is significantly inferior in armor penetration American counterparts. This is due to the greater length of the striking core, which is part of the American ammunition. An obstacle to increasing the length of the projectile (and, hence, armor penetration) is the device of automatic loaders of Russian tanks.

The armor penetration of the core increases with a decrease in its diameter and with an increase in its mass. This contradiction can be solved by using very dense materials. Initially, tungsten was used for the striking elements of such ammunition, but it is very rare, expensive, and also difficult to process.

Depleted uranium has almost the same density as tungsten, and is a virtually free resource for any country that has a nuclear industry.

At present, sub-caliber munitions with a uranium core are in service with the major powers. In the United States, all such ammunition is equipped only with uranium cores.

Depleted uranium has several advantages:

• when passing through the armor, the uranium rod is self-sharpening, which provides better armor penetration, tungsten also has this feature, but it is less pronounced;
• after breaking through the armor, under the influence of high temperatures, the remains of the uranium rod flare up, filling the armored space with poisonous gases.

To date, modern sub-caliber shells have almost reached their maximum efficiency. It can be increased only by increasing the caliber of tank guns, but this will require significant changes in the design of the tank. So far, in the leading tank-building states, they are only engaged in modifying vehicles produced during the Cold War, and are unlikely to take such radical steps.

In the United States, active-rocket projectiles with a kinetic warhead are being developed. This conventional projectile, which immediately after the shot turns on its own upper stage, which significantly increases its speed and armor penetration.

The Americans are also developing a kinetic guided missile, damaging factor which is the uranium rod. After firing from the launch canister, the upper stage turns on, which gives the ammunition a speed of Mach 6.5. Most likely, by 2020 there will be sub-caliber ammunition with a speed of 2000 m/s and higher. This will take their efficiency to a whole new level.

Sub-caliber bullets

In addition to sub-caliber shells, there are bullets that have the same design. Very widely such bullets are used for 12 gauge cartridges.

Sub-caliber bullets of 12 caliber have a smaller mass, after being fired they receive more kinetic energy and, accordingly, have a greater flight range.

Very popular 12-gauge sub-caliber bullets are: Polev's bullet and Kirovchanka. There are other similar 12-gauge ammunition.

Video about sub-caliber ammunition

If you have any questions - leave them in the comments below the article. We or our visitors will be happy to answer them.

This article will look at the various types of ammunition and their armor penetration. Photographs and illustrations of the traces of armor remaining after being hit by a projectile are given, as well as an analysis of the overall effectiveness of various types of ammunition used to destroy tanks and other armored vehicles.
When studying this issue, it should be noted that armor penetration depends not only on the type of projectile, but also on the combination of many other factors: firing range, muzzle velocity, type of armor, armor slope angle, etc. mm armor plates various types. The shelling was carried out with 75-mm armor-piercing shells in order to show the difference in the resistance of armor of the same thickness, but of different types.

The iron armor plate had a brittle fracture of the rear surface, with numerous spalls in the area of ​​the hole. The impact speed is chosen in such a way that the projectile is stuck in the plate. Penetration is nearly achieved with a projectile speed of just 390.3 m/s. The projectile itself was not damaged at all, and will certainly work properly, breaking through such armor.

Iron-nickel armor, without hardening according to the Krupp method (that is, in fact - structural steel) - demonstrated plastic failure with a classic "envelope" (cross-shaped tear on the rear surface), without any traces of fragmentation. As you can see, close to the previous test, the projectile impact speed no longer even leads to through penetration (hit No. I). And only an increase in speed to 437 m / s leads to a violation of the integrity of the rear surface of the armor (the projectile did not penetrate the armor, but a through hole was formed). To achieve a result similar to the first test, it is necessary to bring the speed of the projectile to the armor up to 469.2 m/s (it would not be superfluous to recall that the kinetic energy of the projectile grows in proportion to the square of the speed, i.e. almost one and a half times!). At the same time, the projectile was destroyed, its charging chamber was opened - it will no longer be able to work properly.

Krupp armor - the front layer of high hardness contributed to the splitting of shells, while the softer base of the armor deformed, absorbing the energy of the projectile. The first three shells collapsed almost without even leaving marks on the armor plate. Projectile No. IV, which hit the armor at a speed of 624 m / s, also completely collapsed, but this time almost squeezing out the “cork” in its caliber. We can assume that with a further, even a slight increase in the speed of the meeting, a through penetration will occur. But to overcome the Krupp armor, the projectile had to be given more than 2.5 times more kinetic energy!

Armor-piercing projectile

The most massive type of ammunition used against tanks. And as the name implies, it was created specifically for breaking through armor. According to their design, armor-piercing shells were solid blanks (without an explosive charge in the body) or shells with a chamber (inside which an explosive charge was placed). Blanks were easier to manufacture and hit the crew and mechanisms of an enemy tank only at the point of penetration of the armor. Chamber shells were more difficult to manufacture, but when armor was pierced, explosives exploded in the chamber, causing more damage to the crew and mechanisms of an enemy tank, increasing the likelihood of detonation of ammunition or arson of fuel and lubricants.

Also, the shells were sharp-headed and blunt-headed. Equipped with ballistic tips to give the correct angle when meeting with sloped armor and reduce ricochet.

HEAT projectile

Cumulative projectile. The principle of operation of this armor-piercing ammunition is significantly different from the principle of operation of kinetic ammunition, which includes conventional armor-piercing and sub-caliber projectiles. A cumulative projectile is a thin-walled steel projectile filled with a powerful explosive - RDX, or a mixture of TNT and RDX. At the front of the projectile, explosives have a goblet-shaped recess lined with metal (usually copper). The projectile has a sensitive head fuse. When a projectile collides with armor, an explosive is detonated. At the same time, the lining metal is melted and compressed by an explosion into a thin jet (pestle), flying forward at an extremely high speed and penetrating armor. Armored action is provided by a cumulative jet and splashes of armor metal. The HEAT projectile hole is small and has melted edges, which has led to a common misconception that HEAT rounds“burn through” the armor. The penetration of a HEAT projectile does not depend on the velocity of the projectile and is the same at all distances. Its manufacture is quite simple, the production of the projectile does not require the use of a large amount of scarce metals. The cumulative projectile can be used against infantry and artillery as a high-explosive fragmentation projectile. At the same time, cumulative shells during the war years were characterized by numerous shortcomings. The manufacturing technology of these projectiles was not sufficiently developed, as a result, their penetration was relatively low (approximately corresponded to the caliber of the projectile or slightly higher) and was characterized by instability. The rotation of the projectile at high initial speeds made it difficult for the formation of a cumulative jet, as a result, the cumulative projectiles had a low initial velocity, a small effective range shooting and high dispersion, which was also facilitated by the non-optimal form of the projectile head from the point of view of aerodynamics (its configuration was determined by the presence of a notch). The big problem was the creation of a complex fuse, which should be sensitive enough to quickly undermine the projectile, but stable enough not to explode in the barrel (the USSR was able to work out such a fuse suitable for use in powerful tank and anti-tank guns, only at the end of 1944). The minimum caliber of a cumulative projectile was 75 mm, and the effectiveness of cumulative projectiles of this caliber was greatly reduced. Mass production of HEAT shells required the deployment of large-scale production of hexogen. The most massive HEAT shells were used by the German army (for the first time in the summer-autumn of 1941), mainly from 75 mm caliber guns and howitzers. Soviet army used cumulative shells, created on the basis of captured German ones, from 1942-43, including them in the ammunition of regimental guns and howitzers that had a low muzzle velocity. The British and American armies used shells of this type, mainly in heavy howitzer ammunition. Thus, in the Second World War (unlike the present, when improved shells of this type form the basis of the ammunition load of tank guns), the use of cumulative shells was rather limited, mainly they were considered as a means of anti-tank self-defense of guns that had low initial speeds and low armor penetration by traditional shells (regimental guns, howitzers). At the same time, all participants in the war actively used other anti-tank weapons with cumulative ammunition - grenade launchers (illustration No. 8), aerial bombs, hand grenades.

Sub-caliber projectile

Sub-caliber projectile. This projectile had enough complex structure , which consisted of two main parts - an armor-piercing core and a pallet. The task of the pallet, made of mild steel, was to disperse the projectile in the bore. When the projectile hit the target, the pallet was crushed, and the heavy and hard sharp-headed core made of tungsten carbide pierced the armor. The projectile did not have a bursting charge, ensuring that the target was hit by fragments of the core and fragments of armor heated to high temperatures. Sub-caliber projectiles had significantly less weight than conventional armor-piercing projectiles, which allowed them to accelerate in the gun barrel to significantly higher speeds. As a result, the penetration of sub-caliber shells turned out to be significantly higher. The use of sub-caliber shells made it possible to significantly increase the armor penetration of the existing guns, which made it possible to hit more modern, well-armored armored vehicles even with outdated guns. At the same time, sub-caliber shells had a number of disadvantages. Their shape resembled a coil (there were shells of this type and streamlined shape, but they were much less common), which greatly worsened the ballistics of the projectile, in addition, the light projectile quickly lost speed; as a result, at long distances, the armor penetration of sub-caliber shells dropped dramatically, turning out to be even lower than that of classic armor-piercing shells. Sub-caliber shells did not work well on sloped armor, because under the action of bending loads the hard but brittle core easily broke. The armor-piercing effect of such shells was inferior to armor-piercing caliber shells. Sub-caliber projectiles of small caliber were ineffective against armored vehicles that had protective shields made of thin steel. These shells were expensive and difficult to manufacture, and most importantly, scarce tungsten was used in their manufacture. As a result, the number of sub-caliber shells in the ammunition load of guns during the war years was small, they were allowed to be used only to destroy heavily armored targets at short distances. The German army was the first to use sub-caliber shells in small quantities in 1940 during the fighting in France. In 1941, faced with heavily armored Soviet tanks, the Germans switched to the widespread use of sub-caliber shells, which significantly increased the anti-tank capabilities of their artillery and tanks. However, the shortage of tungsten limited the release of shells of this type; as a result, in 1944, the production of German sub-caliber shells was discontinued, while most of the shells fired during the war years had a small caliber (37-50 mm). Trying to get around the problem of tungsten, the Germans produced Pzgr.40(C) sub-caliber projectiles with a steel core and Pzgr.40(W) surrogate projectiles, which were a sub-caliber projectile without a core. In the USSR, a fairly mass production of sub-caliber shells, created on the basis of captured German ones, began at the beginning of 1943, and most of the shells produced were 45 mm caliber. The production of these shells of larger calibers was limited by the shortage of tungsten, and they were issued to the troops only when there was a threat of an enemy tank attack, and a report was required for each spent shell. Also, sub-caliber shells were used to a limited extent by the British and American armies in the second half of the war.

high-explosive projectile

High-explosive fragmentation projectile. It is a thin-walled steel or steel-cast iron projectile filled with an explosive (usually TNT or ammonite), with a head fuse. Unlike armor-piercing shells, high-explosive shells did not have a tracer. Upon hitting the target, the projectile explodes, hitting the target with fragments and a blast wave, either immediately - a fragmentation action, or with some delay (which allows the projectile to go deeper into the ground) - a high-explosive action. The projectile is intended mainly to destroy openly located and covered infantry, artillery, field shelters (trenches, wood-and-earth firing points), unarmored and lightly armored vehicles. Good armored tanks and self-propelled guns are resistant to high-explosive fragmentation shells. However, projectile impact large caliber can cause the destruction of lightly armored vehicles, and damage to heavily armored tanks, consisting in cracking of armor plates (illustration No. 19), jamming of the turret, failure of instruments and mechanisms, injuries and shell shock to the crew.

Literature / useful materials and links:

• Artillery (State Military Publishing House of the People's Commissariat of Defense of the USSR. Moscow, 1938)
• Artillery Sergeant's Manual ()
• Artillery book. Military publishing house of the Ministry of Defense of the USSR. Moscow - 1953 ()
• Internet materials

Many types of shells are implemented in War Thunder, each of which has its own characteristics. In order to competently compare different shells, to choose the main type of ammunition before the battle, and in battle to use suitable shells for different purposes in different situations, you need to know the basics of their design and principle of operation. This article talks about the types of projectiles and their design, as well as gives advice on their use in combat. Do not neglect this knowledge, because the effectiveness of the weapon largely depends on the shells for it.

Types of tank ammunition

Armor-piercing caliber shells

Chamber and solid armor-piercing shells

As the name implies, the purpose of armor-piercing shells is to penetrate armor and thereby hit a tank. Armor-piercing shells are of two types: chamber and solid. Chamber shells have a special cavity inside - a chamber, in which an explosive is located. When such a projectile penetrates the armor, the fuse is triggered and the projectile explodes. The crew of an enemy tank is hit not only by armor fragments, but also by explosions and fragments of a chamber shell. The explosion does not occur immediately, but with a delay, thanks to which the projectile has time to fly into the tank and explode there, causing the most damage. In addition, the sensitivity of the fuse is set to, for example, 15 mm, that is, the fuse will only work if the thickness of the armor being penetrated is above 15 mm. This is necessary so that the chamber projectile explodes in the fighting compartment when it breaks through the main armor, and does not cock against the screens.

A solid projectile does not have a chamber with an explosive, it is just a metal blank. Of course, solid shells inflict much less damage, but they penetrate a greater thickness of armor than similar chamber shells, since solid shells are more durable and heavier. For example, the armor-piercing chamber projectile BR-350A from the F-34 cannon pierces 80 mm at a right angle at close range, and the solid BR-350SP projectile as much as 105 mm. The use of solid shells is very characteristic of the British school of tank building. Things got to the point that the British removed explosives from American 75-mm chamber shells, turning them into solid ones.

The lethal force of solid shells depends on the ratio of the thickness of the armor and the armor penetration of the shell:

• If the armor is too thin, then the projectile will pierce through it and damage only those elements that it hits along the way.
• If the armor is too thick (on the border of penetration), then small non-lethal fragments are formed that will not cause much harm.
• Maximum armor action - in case of penetration of sufficiently thick armor, while the penetration of the projectile should not be completely used up.

Thus, in the presence of several solid shells, the best armor action will be with the one with greater armor penetration. As for chamber shells, the damage also depends on the amount of explosive in TNT equivalent, as well as on whether the fuse worked or not.

Sharp-headed and blunt-headed armor-piercing shells

An oblique blow to the armor: a - a sharp-headed projectile; b - blunt projectile; c - arrow-shaped sub-caliber projectile

Armor-piercing shells are divided not only into chamber and solid shells, but also into sharp-headed and dumb-headed ones. Pointed shells pierce thicker armor at a right angle, since at the moment of impact with the armor, all the impact force falls on a small area of ​​the armor plate. However, the efficiency of work on sloping armor in sharp-headed projectiles is lower due to a greater tendency to ricochet at large angles of impact with the armor. Vice versa, blunt projectiles they penetrate thicker armor at an angle than sharp-headed ones, but have less armor penetration at a right angle. Let's take for example the armor-piercing chamber shells of the T-34-85 tank. At a distance of 10 meters, the BR-365K sharp-headed projectile penetrates 145 mm at a right angle and 52 mm at an angle of 30 °, and the BR-365A blunt-headed projectile penetrates 142 mm at a right angle, but 58 mm at an angle of 30 °.

In addition to sharp-headed and blunt-headed shells, there are sharp-headed shells with an armor-piercing tip. When meeting armor plate at a right angle, such a projectile works like a sharp-headed projectile and has good armor penetration compared to a similar blunt-headed projectile. When hitting sloping armor, the armor-piercing tip “bites” the projectile, preventing ricochet, and the projectile works like a dumb-ass.

However, sharp-headed shells with an armor-piercing tip, like blunt-headed shells, have a significant drawback - greater aerodynamic resistance, due to which armor penetration drops more at a distance than sharp-headed shells. To improve aerodynamics, ballistic caps are used, due to which armor penetration is increased at medium and long distances. For example, on the German 128 mm KwK 44 L/55 gun, two armor-piercing chamber shells are available, one with a ballistic cap and the other without it. Armor-piercing sharp-headed projectile with an armor-piercing tip PzGr at a right angle pierces 266 mm at 10 meters and 157 mm at 2000 meters. But an armor-piercing projectile with an armor-piercing tip and a ballistic cap PzGr 43 at a right angle pierces 269 mm at 10 meters and 208 mm at 2000 meters. In close combat, there are no special differences between them, but at long distances the difference in armor penetration is huge.

Armor-piercing chamber shells with an armor-piercing tip and a ballistic cap are the most versatile type of armor-piercing ammunition, which combines the advantages of sharp-headed and blunt-headed projectiles.

Table of armor-piercing shells

Sharp-headed armor-piercing shells can be chamber or solid. The same applies to blunt-headed shells, as well as sharp-headed shells with an armor-piercing tip, and so on. Let's put it all together possible options to the table. Under the icon of each projectile, the abbreviated names of the projectile type are written in English terminology, these are the terms used in the book "WWII Ballistics: Armor and Gunnery", according to which many shells in the game are configured. If you hover over the abbreviated name with the mouse cursor, a hint with decoding and translation will appear.

	dumb-headed (with ballistic cap)	sharp-headed	sharp-headed with armor-piercing tip	sharp-headed with armor-piercing tip and ballistic cap
Solid projectile	APBC	AP	APC	APCBC
Chamber projectile		APHE	APHEC

Sub-caliber shells

Coil sub-caliber projectiles

The action of the sub-caliber projectile:
1 - ballistic cap
2 - body
3 - core

Armor-piercing caliber shells have been described above. They are called caliber because the diameter of their warhead is equal to the caliber of the gun. There are also armor-piercing sub-caliber shells, the warhead diameter of which is smaller than the caliber of the gun. The simplest type of sub-caliber projectiles is coil (APCR - Armor-Piercing Composite Rigid). The coil sub-caliber projectile consists of three parts: a body, a ballistic cap and a core. The body serves to disperse the projectile in the barrel. At the moment of meeting with the armor, the ballistic cap and the body are crushed, and the core pierces the armor, hitting the tank with shrapnel.

At close range, sub-caliber shells penetrate thicker armor than caliber shells. Firstly, the sabot projectile is smaller and lighter than a conventional armor-piercing projectile, thanks to which it accelerates to higher speeds. Secondly, the core of the projectile is made of hard alloys with a high specific gravity. Thirdly, due to the small size of the core at the moment of contact with the armor, the impact energy falls on a small area of ​​​​the armor.

But coil sub-caliber shells also have significant drawbacks. Due to their relatively light weight, sub-caliber shells are ineffective at long distances, they lose energy faster, hence the drop in accuracy and armor penetration. The core does not have an explosive charge, therefore, in terms of armor action, sub-caliber shells are much weaker than chamber shells. Finally, sub-caliber shells do not work well against sloped armor.

Coil sub-caliber shells were effective only in close combat and were used in cases where enemy tanks were invulnerable against caliber armor-piercing shells. The use of sub-caliber shells made it possible to significantly increase the armor penetration of the existing guns, which made it possible to hit more modern, well-armored armored vehicles even with outdated guns.

Sub-caliber projectiles with a detachable pallet

APDS projectile and its core

Sectional view of an APDS projectile, showing the ballistic-tipped core

Armor-Piercing Discarding Sabot (APDS) - a further development of the design of sabot projectiles.

Coil sub-caliber projectiles had a significant drawback: the hull flew along with the core, increasing aerodynamic drag and, as a result, a drop in accuracy and armor penetration at a distance. For sub-caliber shells with a detachable pallet, a detachable pallet was used instead of the body, which first dispersed the projectile in the gun barrel, and then separated from the core by air resistance. The core flew to the target without a pallet and, due to the significantly lower aerodynamic resistance, did not lose armor penetration at a distance as quickly as coil sub-caliber shells.

During the Second World War, sub-caliber shells with a detachable pallet were distinguished by record-breaking armor penetration and flight speed. For example, the Shot SV Mk.1 sub-caliber projectile for the 17-pounder accelerated to 1203 m/s and pierced 228 mm of soft armor at a right angle at 10 meters, while the Shot Mk.8 armor-piercing caliber projectile only 171 mm under the same conditions.

Sub-caliber feathered shells

Separation of the pallet from BOPS

BOPS projectile

Armor-piercing feathered sabot projectile (APFSDS - Armor-Piercing Fin-Stabilized Discarding Sabot) - the most modern look armor-piercing projectiles, designed to destroy heavily armored vehicles protected the latest species armor and active protection.

These shells are a further development of sub-caliber shells with a detachable pallet, they also have great length and smaller cross section. Spin stabilization is not very effective for high aspect ratio projectiles, so armor piercing finned sabots (BOPS for short) are stabilized by the fins and are generally used to fire smoothbore guns (however, early BOPS and some modern ones are designed to fire rifled guns).

Modern BOPS projectiles have a diameter of 2-3 cm and a length of 50-60 cm. To maximize the specific pressure and kinetic energy of the projectile, high-density materials are used in the manufacture of ammunition - tungsten carbide or an alloy based on depleted uranium. The muzzle velocity of the BOPS is up to 1900 m / s.

Concrete-piercing projectiles

The concrete projectile is artillery shell, designed to destroy long-term fortifications and solid buildings of capital construction, as well as to destroy manpower sheltered in them and military equipment enemy. Often, concrete-piercing shells were used to destroy concrete pillboxes.

In terms of design, concrete-piercing shells occupy an intermediate position between armor-piercing chamber and high-explosive fragmentation shells. Compared to high-explosive fragmentation projectiles of the same caliber, with a close destructive potential of the explosive charge, concrete-piercing ammunition has a more massive and durable body, which allows them to penetrate deep into reinforced concrete, stone and brick barriers. Compared to armor-piercing chamber shells, concrete-piercing shells have more explosives, but a less durable body, so concrete-piercing shells are inferior to them in armor penetration.

The G-530 concrete-piercing projectile weighing 40 kg is included in the ammunition load of the KV-2 tank, the main purpose of which was the destruction of pillboxes and other fortifications.

HEAT rounds

Rotating HEAT projectiles

The device of the cumulative projectile:
1 - fairing
2 - air cavity
3 - metal cladding
4 - detonator
5 - explosive
6 - piezoelectric fuse

A cumulative projectile (HEAT - High-Explosive Anti-Tank) differs significantly from kinetic ammunition, which includes conventional armor-piercing and sub-caliber projectiles, in terms of the principle of operation. It is a thin-walled steel projectile filled with a powerful explosive - RDX, or a mixture of TNT and RDX. In front of the projectile in explosives there is a goblet-shaped or cone-shaped recess lined with metal (usually copper) - a focusing funnel. The projectile has a sensitive head fuse.

When a projectile collides with armor, an explosive is detonated. Due to the presence of a focusing funnel in the projectile, part of the explosion energy is concentrated at one small point, forming a thin cumulative jet consisting of the metal of the lining of the same funnel and explosion products. The cumulative jet flies forward at great speed (approximately 5,000 - 10,000 m / s) and passes through the armor due to the enormous pressure it creates (like a needle through oil), under the influence of which any metal enters a state of superfluidity or, in other words, leads itself as a liquid. The armored damaging effect is provided both by the cumulative jet itself and by hot drops of pierced armor squeezed inward.

The most important advantage of a HEAT projectile is that its armor penetration does not depend on the velocity of the projectile and is the same at all distances. That is why cumulative shells were used on howitzers, since conventional armor-piercing shells would be ineffective for them due to their low flight speed. But the cumulative shells of the Second World War also had significant drawbacks that limited their use. The rotation of the projectile at high initial speeds made it difficult to form a cumulative jet, as a result, the cumulative projectiles had a low initial speed, a small effective range and high dispersion, which was also facilitated by the shape of the projectile head, which was not optimal from the point of view of aerodynamics. The manufacturing technology of these shells at that time was not sufficiently developed, so their armor penetration was relatively low (approximately corresponded to the caliber of the projectile or slightly higher) and was characterized by instability.

Non-rotating (feathered) cumulative projectiles

Non-rotating (feathered) cumulative projectiles (HEAT-FS - High-Explosive Anti-Tank Fin-Stabilised) are further development cumulative ammunition. Unlike early cumulative projectiles, they are stabilized in flight not by rotation, but by folding fins. The absence of rotation improves the formation of a cumulative jet and significantly increases armor penetration, while removing all restrictions on the speed of the projectile, which can exceed 1000 m/s. So, for early cumulative shells, typical armor penetration was 1-1.5 calibers, while for post-war shells it was 4 or more. However, feathered projectiles have a slightly lower armor effect compared to conventional HEAT projectiles.

Fragmentation and high-explosive shells

High-explosive shells

A high-explosive fragmentation projectile (HE - High-Explosive) is a thin-walled steel or cast iron projectile filled with an explosive (usually TNT or ammonite), with a head fuse. Upon hitting the target, the projectile immediately explodes, hitting the target with fragments and an explosive wave. Compared to concrete-piercing and armor-piercing chamber shells, high-explosive fragmentation shells have very thin walls, but they have more explosives.

The main purpose of high-explosive fragmentation shells is to defeat enemy manpower, as well as unarmored and lightly armored vehicles. Large-caliber high-explosive fragmentation shells can be very effectively used to destroy lightly armored tanks and self-propelled guns, as they break through relatively thin armor and incapacitate the crew with the force of the explosion. Tanks and self-propelled guns with anti-projectile armor are resistant to high-explosive fragmentation shells. However, large-caliber projectiles can even hit them: the explosion destroys the tracks, damages the gun barrel, jams the turret, and the crew is injured and shell-shocked.

Shrapnel shells

The shrapnel projectile is a cylindrical body, divided by a partition (diaphragm) into 2 compartments. An explosive charge is placed in the bottom compartment, and spherical bullets are in the other compartment. A tube filled with a slowly burning pyrotechnic composition passes along the axis of the projectile.

The main purpose of the shrapnel projectile is to defeat the enemy's manpower. It happens in the following way. At the moment of the shot, the composition in the tube ignites. Gradually, it burns out and transfers the fire to the explosive charge. The charge ignites and explodes, squeezing out a partition with bullets. The head of the projectile comes off and the bullets fly out along the axis of the projectile, deviating slightly to the sides and hitting the enemy infantry.

In the absence of armor-piercing shells in the early stages of the war, gunners often used shrapnel shells with a tube set "on impact". In terms of its qualities, such a projectile occupied an intermediate position between high-explosive fragmentation and armor-piercing, which is reflected in the game.

Armor-piercing shells

Armor-piercing high-explosive projectile (HESH - High Explosive Squash Head) - post-war type anti-tank projectile, the principle of operation of which is based on the detonation of a plastic explosive on the surface of the armor, which causes the armor fragments on the back to break off and damage the fighting compartment of the vehicle. An armor-piercing high-explosive projectile has a body with relatively thin walls, designed for plastic deformation when it encounters an obstacle, as well as a bottom fuse. The charge of an armor-piercing high-explosive projectile consists of a plastic explosive that “spreads” over the surface of the armor when the projectile meets an obstacle.

After “spreading”, the charge is detonated by a slow-acting bottom fuse, which causes the destruction of the rear surface of the armor and the formation of spalls that can hit the internal equipment of the vehicle or crew members. In some cases, penetrating armor can also occur in the form of a puncture, a breach, or a broken plug. The penetrating ability of an armor-piercing high-explosive projectile depends less on the angle of the armor in comparison with conventional armor-piercing projectiles.

ATGM Malyutka (1 generation)

Shillelagh ATGM (2 generations)

Anti-tank guided missiles

An anti-tank guided missile (ATGM) is a guided missile designed to destroy tanks and other armored targets. The former name of the ATGM is "anti-tank guided missile". ATGMs in the game are solid-propellant missiles equipped with on-board control systems (operating on the operator's commands) and flight stabilization, devices for receiving and decrypting control signals received via wires (or via infrared or radio command control channels). Warhead cumulative, with armor penetration of 400-600 mm. The flight speed of missiles is only 150-323 m / s, but the target can be successfully hit at a distance of up to 3 kilometers.

The game features ATGMs of two generations:

• First generation (manual command guidance system)- in reality, they are manually controlled by the operator using a joystick, eng. MCLOS. In realistic and simulation modes, these missiles are controlled using the WSAD keys.
• Second generation (semi-automatic command guidance system)- in reality and in all game modes, they are controlled by pointing the sight at the target, eng. SACLOS. The reticle in the game is either the center of the crosshair of the optical sight, or a large white round marker (reload indicator) in the third person view.

In arcade mode, there is no difference between the generations of rockets, they are all controlled with the help of a sight, like second-generation rockets.

ATGMs are also distinguished by the launch method.

• 1) Launched from the channel of the tank barrel. To do this, you need either a smooth barrel: an example is the smooth barrel of a 125-mm gun of the T-64 tank. Or a keyway is made in a rifled barrel, where a rocket is inserted, for example, in the Sheridan tank.
• 2) Launched from guides. Closed, tubular (or square), for example, like the RakJPz 2 tank destroyer with the HOT-1 ATGM. Or open, rail (for example, like the IT-1 tank destroyer with the 2K4 Dragon ATGM).

As a rule, the more modern and the larger the caliber of the ATGM, the more it penetrates. ATGMs were constantly improved - manufacturing technology, materials science, and explosives improved. The penetrating effect of ATGMs (as well as cumulative projectiles) can be completely or partially neutralized combined armor and dynamic protection. As well as special anti-cumulative armor screens located at some distance from the main armor.

Appearance and device of shells

Armor-piercing sharp-headed chamber projectile



Sharp-headed projectile with armor-piercing tip



Sharp-headed projectile with armor-piercing tip and ballistic cap



Armor-piercing blunt projectile with ballistic cap



Sub-caliber projectile



Sub-caliber projectile with detachable pallet



HEAT projectile



Non-rotating (feathered) cumulative projectile

• 

  A denormalization phenomenon that increases the path of a projectile through armor

  Starting with game version 1.49, the effect of shells on sloped armor has been redesigned. Now the value of the reduced armor thickness (armor thickness ÷ cosine of the angle of inclination) is valid only for calculating the penetration of HEAT projectiles. For armor-piercing and especially sub-caliber shells, the penetration of sloping armor was significantly reduced due to the denormalization effect, when a short shell turns around during penetration, and its path in the armor increases.

  So, at an angle of inclination of the armor of 60 °, penetration for all shells fell by about 2 times. Now this is true only for cumulative and armor-piercing high-explosive shells. For armor-piercing shells, penetration in this case drops by 2.3-2.9 times, for conventional sub-caliber shells - by 3-4 times, and for sub-caliber shells with a detachable pallet (including BOPS) - by 2.5 times.

  List of shells in order of deterioration of their work on sloped armor:

  1. Cumulative And armor-piercing high-explosive- the most efficient.
  2. Armor-piercing blunt And armor-piercing sharp-headed with an armor-piercing tip.
  3. Armor-piercing sub-caliber with detachable pallet And BOPS.
  4. Armor-piercing sharp-headed And shrapnel.
  5. Armor-piercing sub-caliber- the most inefficient.

  Here, a high-explosive fragmentation projectile stands apart, in which the probability of penetrating the armor does not depend on its angle of inclination at all (provided that no ricochet has occurred).

  Armor-piercing shells

  For such projectiles, the fuse is cocked at the moment of penetration of the armor and undermines the projectile after a certain time, which ensures a very high armor effect. Two important values ​​are specified in the parameters of the projectile: fuse sensitivity and fuse delay.

  If the thickness of the armor is less than the sensitivity of the fuse, then the explosion will not occur, and the projectile will work like a regular solid one, damaging only those modules that are in its path, or simply fly through the target without causing damage. Therefore, when firing at unarmored targets, chamber shells are not very effective (as well as all others, except for high-explosive and shrapnel).

  The fuse delay determines the time after which the projectile will explode after breaking through the armor. Too little delay (in particular, for the Soviet MD-5 fuse) leads to the fact that when it hits hinged element tank (screen, track, undercarriage, caterpillar), the projectile explodes almost immediately and does not have time to penetrate the armor. Therefore, when firing at shielded tanks, it is better not to use such shells. Too much delay of the fuse can cause the projectile to go right through and explode outside the tank (although such cases are very rare).

  If a chamber projectile is detonated in a fuel tank or in an ammunition rack, then with a high probability an explosion will occur and the tank will be destroyed.

  Armor-piercing sharp-headed and blunt-headed projectiles

  Depending on the shape of the armor-piercing part of the projectile, its tendency to ricochet, armor penetration and normalization differ. General rule: blunt-headed shells are best used on opponents with sloped armor, and sharp-headed ones - if the armor is not sloped. However, the difference in armor penetration in both types is not very large.

  The presence of armor-piercing and / or ballistic caps significantly improves the properties of the projectile.

  Sub-caliber shells

  This type of projectile is distinguished by high armor penetration at short distances and a very high flight speed, which makes it easier to shoot at moving targets.

  However, when armor is penetrated, only a thin hard-alloy rod appears in the armored space, which causes damage only to those modules and crew members in which it hits (unlike an armor-piercing chamber projectile, which fills everything with fragments fighting compartment). Therefore, in order to effectively destroy a tank with a sub-caliber projectile, it is necessary to shoot at its weak spots: engine, ammunition rack, fuel tanks. But even in this case, one hit may not be enough to disable the tank. If you shoot at random (especially at the same point), it may take a lot of shots to disable the tank, and the enemy may get ahead of you.

  Another problem with sub-caliber projectiles is a strong loss of armor penetration with distance due to their low mass. Studying the armor penetration tables shows at what distance you need to switch to a regular armor-piercing projectile, which, in addition, has a much greater lethality.

  HEAT rounds

  The armor penetration of these shells does not depend on the distance, which allows them to be used with equal efficiency for both close and long-range combat. However, due to design features, HEAT rounds often have a lower flight speed than other types, as a result of which the shot trajectory becomes hinged, accuracy suffers, and hitting moving targets (especially on long distance) becomes very difficult.

  The principle of operation of the cumulative projectile also determines its not very high damaging ability compared to the armor-piercing chamber projectile: the cumulative jet flies for a limited distance inside the tank and inflicts damage only to those components and crew members in which it directly hit. Therefore, when using a cumulative projectile, one should aim just as carefully as in the case of a sub-caliber one.

  If the cumulative projectile hit not the armor, but the hinged element of the tank (screen, track, caterpillar, undercarriage), then it will explode on this element, and the armor penetration of the cumulative jet will significantly decrease (each centimeter of the jet flight in the air reduces armor penetration by 1 mm) . Therefore, other types of shells should be used against tanks with screens, and one should not hope to penetrate the armor with HEAT shells by shooting at the tracks, undercarriage and gun mantlet. Remember that a premature detonation of a projectile can cause any obstacle - a fence, a tree, any building.

  HEAT shells in life and in the game have a high-explosive action, that is, they also work as high-explosive fragmentation shells of reduced power (a light body gives fewer fragments). Thus, large-caliber cumulative projectiles can be quite successfully used instead of high-explosive fragmentation when firing at lightly armored vehicles.

  High-explosive shells

  The striking ability of these shells depends on the ratio of the caliber of your gun and the armor of your target. Thus, shells with a caliber of 50 mm or less are only effective against aircraft and trucks, 75-85 mm - against light tanks with bulletproof armor, 122 mm - against medium tanks such as T-34, 152 mm - against all tanks, with the exception of head-on shooting at the most armored vehicles.

  However, it must be remembered that the damage inflicted significantly depends on the specific point of impact, so there are cases when even a 122-152 mm caliber projectile causes very minor damage. And in the case of guns with a smaller caliber, in doubtful cases, it is better to use an armor-piercing chamber or shrapnel projectile, which have greater penetration and high lethality.

  Shells - part 2

  What is the best way to shoot? Overview tank shells by _Omero_